-- *****************************************************************
-- CISCO-DS1-CAPABILITY
--
-- AGENT-CAPABILITIES MIB for DS1-MIB for CISCO Products
--
-- December 2003, Yizhong Shen
--
-- Copyright(c) 2002, 2003, 2005 by Cisco Systems,Inc.
--
-- *****************************************************************CISCO-DS1-CAPABILITY DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITYFROM SNMPv2-SMI
AGENT-CAPABILITIESFROM SNMPv2-CONF
ciscoAgentCapability
FROM CISCO-SMI;ciscoDs1Capability MODULE-IDENTITYLAST-UPDATED"200507110000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO" Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-wanatm@cisco.com"DESCRIPTION"The agent capabilities for DS1-MIB for Cisco Products Series.
- ciscoDs1AxsmeCapabilityV3R00 is for
Enhanced ATM Switch Service Module(AXSM-E), and
Enhanced Processor Switch Module 1(PXM1E) uplink.
- ciscoDs1CapabilityV5R00 is for Voice Switch
Service Module(VXSM) and MPSM Module Release 5.0.0."REVISION"200507110000Z"DESCRIPTION"Added ciscoDs1CapabilityV5R100 for MPSM and VXSM support in
MGX8880 release 5.1.0."REVISION"200312220000Z"DESCRIPTION"ciscoDs1CapabilityV5R00 added for MPSM and VXSM support."REVISION"200204280000Z"DESCRIPTION"Initial version of this MIB module."::={ ciscoAgentCapability 273}ciscoDs1AxsmeCapabilityV3R00 AGENT-CAPABILITIESPRODUCT-RELEASE"MGX8850 Release 3.0"STATUScurrent
DESCRIPTION"DS1-MIB Capabilities."SUPPORTS DS1-MIB
INCLUDES{ ds1NearEndConfigGroup, ds1NearEndStatisticsGroup,
ds1FarEndGroup }VARIATION dsx1LineType
SYNTAXINTEGER{dsx1ESF(2),
dsx1E1CRCMF(7)}ACCESSread-onlyDESCRIPTION"Supported with limitation.
dsx1ESF(2) used only for T1 mode,
dsx1E1CRCMF(7) used only for E1 mode."VARIATION dsx1LineCoding
SYNTAXINTEGER{dsx1B8ZS(2),
dsx1HDB3(3)}ACCESSread-onlyDESCRIPTION"Supported with limitation.
dsx1B8ZS(2) used only for T1 mode,
dsx1HDB3(3) used only for E1 mode."
VARIATION dsx1SendCode
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1CircuitIdentifier
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1LoopbackConfig
SYNTAXINTEGER{dsx1NoLoop(1),
dsx1LineLoop(3),
dsx1InwardLoop(5)}DESCRIPTION"Supported with limitation."VARIATION dsx1SignalMode
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1Fdl
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1LineStatusLastChange
ACCESSnot-implementedDESCRIPTION"Not Supported."
VARIATION dsx1LineStatusChangeTrapEnable
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1LoopbackStatus
DESCRIPTION"The agent only sets following bits:
1 dsx1NoLoopback
16 dsx1NearEndInwardLoopback
64 dsx1FarEndLineLoopback."VARIATION dsx1Ds1ChannelNumber
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1Channelization
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1CurrentCSSs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1CurrentBESs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1CurrentDMs
ACCESSnot-implementedDESCRIPTION"Not Supported."
VARIATION dsx1IntervalCSSs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1IntervalBESs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1IntervalDMs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1TotalCSSs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1TotalBESs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1TotalDMs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1FarEndCurrentCSSs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1FarEndCurrentBESs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1FarEndCurrentDMs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1FarEndIntervalCSSs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1FarEndIntervalBESs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1FarEndIntervalDMs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1FarEndTotalCSSs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1FarEndTotalBESs
ACCESSnot-implementedDESCRIPTION"Not Supported."VARIATION dsx1FarEndTotalDMs
ACCESSnot-implemented
DESCRIPTION"Not Supported."::={ ciscoDs1Capability 1}ciscoDs1CapabilityV5R00 AGENT-CAPABILITIESPRODUCT-RELEASE"MGX8850 Release 5.0.0"STATUScurrentDESCRIPTION"DS1 MIB capabilities for VXSM and
MPSM in release 5.0.0"SUPPORTS DS1-MIB
INCLUDES{ ds1NearEndConfigGroup,
ds1NearEndStatisticsGroup,
ds1FarEndGroup,
ds1NearEndOptionalConfigGroup
}--
-- VXSM variation
--VARIATION dsx1LineCoding
DESCRIPTION"Only supported by T1/E1 card
(entPhysicalVendorType is cevVxsm48t1e1)."--
-- VXSM variation
--VARIATION dsx1LineLength
SYNTAXINTEGER(0..200)DESCRIPTION"Only supported by T1/E1 card
(entPhysicalVendorType is cevVxsm48t1e1),
for T1 only."VARIATION dsx1CircuitIdentifier
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1LineStatusLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1Ds1ChannelNumber
ACCESSnot-implementedDESCRIPTION"Not supported."--
-- VXSM variation
--VARIATION dsx1LineMode
DESCRIPTION"Only supported by T1/E1 card
(entPhysicalVendorType is cevVxsm48t1e1),
for T1 only."--
-- VXSM variation
--VARIATION dsx1LineBuildOut
DESCRIPTION"Only supported by T1/E1 card
(entPhysicalVendorType is cevVxsm48t1e1),
for T1 only."VARIATION dsx1CurrentDMs
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1IntervalDMs
ACCESSnot-implemented
DESCRIPTION"Not supported."VARIATION dsx1TotalDMs
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1FarEndCurrentDMs
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1FarEndIntervalDMs
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1FarEndTotalDMs
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1LineType
SYNTAXINTEGER{ dsx1ESF(2),
dsx1D4(3),
dsx1E1(4),
dsx1E1CRC(5),
dsx1E1MF(6),
dsx1E1CRCMF(7),
dsx1E1Q50(12),
dsx1E1Q50CRC(13)}DESCRIPTION"Limited data values are supported.
For T1, valid values are 2 and 3.
For E1, valud values are 4..7, 12 and 13."VARIATION dsx1SendCode
SYNTAXINTEGER{ dsx1SendNoCode (1),
dsx1SendLineCode (2),
dsx1SendResetCode(4)}DESCRIPTION"dsx1SendPayloadCode(3),
dsx1SendQRS(5),
dsx1Send511Pattern(6),
dsx1Send3in24Pattern(7),
dsx1SendOtherTestPattern(8)
are not supported on T1.
This object is not supported on E1."VARIATION dsx1LoopbackConfig
SYNTAXINTEGER{ dsx1NoLoop (1),
dsx1LineLoop (3),
dsx1InwardLoop(5)}DESCRIPTION"dsx1PayloadLoop(2), dsx1OtherLoop(4),
and dsx1DualLoop(6) are not supported."VARIATION dsx1LineStatus
DESCRIPTION"dsx1OtherFailure (bit 4096) is used to indicate
the line is in BERT testing."VARIATION dsx1SignalMode
SYNTAXINTEGER{ none (1),
robbedBit (2),
bitOriented (3),
messageOriented (4)}DESCRIPTION"other(5) is not supported.
For T1, valid values are 1, 2 and 4.
For E1, valid values are 1, 3 and 4."VARIATION dsx1Fdl
SYNTAXINTEGER(2..2)
ACCESSread-onlyDESCRIPTION"Only dsx1AnsiT1403(2) is supported.
Set is not allowed."VARIATION dsx1LineStatusChangeTrapEnable
DEFVAL{ enabled }DESCRIPTION"The initial value is enabled(1)."VARIATION dsx1Channelization
SYNTAXINTEGER{ enabledDs0(2)}ACCESSread-onlyDESCRIPTION"disabled(1) and enabledDs1(3) are not supported.
Set is not allowed."VARIATION dsx1FarEndCurrentTable
DESCRIPTION"It is not supported on E1."VARIATION dsx1FarEndIntervalTable
DESCRIPTION"It is not supported on E1."VARIATION dsx1FarEndTotalTable
DESCRIPTION"It is not supported on E1."::={ ciscoDs1Capability 2}
ciscoDs1CapabilityV5R100 AGENT-CAPABILITIESPRODUCT-RELEASE"MGX8880 Release 5.1.0"STATUScurrentDESCRIPTION"DS1 MIB capabilities for VXSM and
MPSM in release 5.1.0"SUPPORTS DS1-MIB
INCLUDES{ ds1NearEndConfigGroup,
ds1NearEndStatisticsGroup,
ds1FarEndGroup,
ds1NearEndOptionalConfigGroup
}--
-- VXSM variation
--VARIATION dsx1LineCoding
DESCRIPTION"Only supported by T1/E1 card
(entPhysicalVendorType is cevVxsm48t1e1)."--
-- VXSM variation
--VARIATION dsx1LineLength
SYNTAXINTEGER(0..200)DESCRIPTION"Only supported by T1/E1 card
(entPhysicalVendorType is cevVxsm48t1e1),
for T1 only."VARIATION dsx1CircuitIdentifier
ACCESSnot-implemented
DESCRIPTION"Not supported."VARIATION dsx1LineStatusLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1Ds1ChannelNumber
ACCESSnot-implementedDESCRIPTION"Not supported."--
-- VXSM variation
--VARIATION dsx1LineMode
DESCRIPTION"Only supported by T1/E1 card
(entPhysicalVendorType is cevVxsm48t1e1),
for T1 only."--
-- VXSM variation
--VARIATION dsx1LineBuildOut
DESCRIPTION"Only supported by T1/E1 card
(entPhysicalVendorType is cevVxsm48t1e1),
for T1 only."VARIATION dsx1CurrentDMs
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1IntervalDMs
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1TotalDMs
ACCESSnot-implemented
DESCRIPTION"Not supported."VARIATION dsx1FarEndCurrentDMs
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1FarEndIntervalDMs
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1FarEndTotalDMs
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION dsx1LineType
SYNTAXINTEGER{ dsx1ESF(2),
dsx1D4(3),
dsx1E1(4),
dsx1E1CRC(5),
dsx1E1MF(6),
dsx1E1CRCMF(7),
dsx1E1Q50(12),
dsx1E1Q50CRC(13)}DESCRIPTION"Limited data values are supported.
For T1, valid values are 2 and 3.
For E1, valud values are 4..7, 12 and 13."VARIATION dsx1SendCode
SYNTAXINTEGER{ dsx1SendNoCode (1),
dsx1SendLineCode (2),
dsx1SendResetCode(4)}DESCRIPTION"dsx1SendPayloadCode(3),
dsx1SendQRS(5),
dsx1Send511Pattern(6),
dsx1Send3in24Pattern(7),
dsx1SendOtherTestPattern(8)
are not supported on T1.
This object is not supported on E1."VARIATION dsx1LoopbackConfig
SYNTAXINTEGER{ dsx1NoLoop (1),
dsx1LineLoop (3),
dsx1InwardLoop(5)}DESCRIPTION"dsx1PayloadLoop(2), dsx1OtherLoop(4),
and dsx1DualLoop(6) are not supported."VARIATION dsx1LineStatus
DESCRIPTION"dsx1OtherFailure (bit 4096) is used to indicate
the line is in BERT testing."VARIATION dsx1SignalMode
SYNTAXINTEGER{ none (1),
robbedBit (2),
bitOriented (3)}DESCRIPTION"other(5) is not supported.
For T1, valid values are 1, and 2
For E1, valid values are 1, and 3."VARIATION dsx1Fdl
SYNTAXINTEGER(2..2)ACCESSread-onlyDESCRIPTION"Only dsx1AnsiT1403(2) is supported.
Set is not allowed."VARIATION dsx1LineStatusChangeTrapEnable
DEFVAL{ enabled }DESCRIPTION"The initial value is enabled(1)."VARIATION dsx1Channelization
SYNTAXINTEGER{ enabledDs0(2)}ACCESSread-onlyDESCRIPTION"disabled(1) and enabledDs1(3) are not supported.
Set is not allowed."VARIATION dsx1FarEndCurrentTable
DESCRIPTION"It is not supported on E1."VARIATION dsx1FarEndIntervalTable
DESCRIPTION"It is not supported on E1."VARIATION dsx1FarEndTotalTable
DESCRIPTION"It is not supported on E1."::={ ciscoDs1Capability 3}END